Sunday, November 22, 2026

Boom-to-Mast Clamp Replacement

We don't often describe in loving detail the clamps that hold our yagis together:

  • Tubes within an element, or boom
  • Element to boom
  • Boom to mast
  • Mast to bearings and rotators
  • Boom truss to mast

They mostly involve mechanical mating of (typically in North American products) round structural components to the same. Nesting tubes and pipes are relatively easy but not so for those that meet at an angle, usually a right angle. It requires an intermediate component such as a plate. 

Commercial antenna manufacturers have developed proprietary methods while home brewers use designs that are easily implemented with commonly found hardware. Antenna manufacturers and others may offer clamps for individual sale. I prefer to make my own. 

There are specialty products in the commercial tower business that hams rarely use since they tend to be heavy and expensive, and not found in the inventories of ham retailers. I've used them on occasion when I scrounged them or when they're already found on a tower I'm working on. For example, a commercial services tower adapted to ham use, such as for repeater installation.

For my own yagis I stick to the most common solution: round structural components are clamped to opposite sides of a flat plate. It's simple and effective, and easily fabricated in the home workshop. There are also effective diameter equations (by W6NL and others) for these clamps that allow accurate yagi design in modelling software.

I have a lot of scrounged aluminum plate. Most of it is ¼" thick. That's the bare minimum. For larger yagis I use ⅜" aluminum or ¼" steel. The most extreme examples are probably the ½" boom-to-mast clamp and ⅜" steel plate element-to-boom clamps on my 300 lb 3-element 40 meter yagi.

The side-mounted lower 5-element yagi of the 15 meter stack was made partially rotatable this year. I used a ¼" aluminum plates from my junk box to make the boom-to-mast clamp. That turned out to be a mistake. The problem was that accidental over-rotation (I have no software rotation limits, yet) causes the boom to strike the tower. There are rubber bumpers installed to soften impacts. The impact occasionally shifted the boom-to-mast clamp several degrees on the mast. Very soon the yagi direction and direction indicator of the Hy-Gain Ham IV were far out of alignment.

After ensuring that it wasn't the mast turning within the rotator mast clamp -- a common problem with large yagis and this class or rotators -- I took the usual route in an attempt to stop the problem recurring. That was to further tighten the saddle clamps securing the mast to the flat aluminum plate. The problem soon recurred.

The next step was to inspect the mast and clamps. The aluminum mast (6061-T6) was scored by the inexpensive steel saddle clamps during those rotation events, and possibly also from the clamping force (steel is harder than aluminum alloy). I also discovered that further tightening of the clamp nuts deformed the aluminum plate. When the metal yielded to the torque the clamping force was reduced, thus returning the clamping force to its previous level.

That was when I realized that I made a poor choice for the plate. It was time to replace it. Since I had ample 3/16" steel plate on hand and no ⅜" aluminum plate left I went with the former. I also used this steel on the recently built 3-element 15 and 20 meter yagis fixed south. 

It was timely that I replenished my steel stock a few months ago. Although steel plate is more difficult to cut and drill than aluminum, it isn't difficult in a well-equipped workshop. Most rust prevention paints protect them from the elements as does cold galvanizing compound. Similarly coated steel has weathered well over the years at my station.

The next time I was on that tower I carefully measured the clamps for the boom and mast and machined the steel plate to be a direct replacement using the same hardware. After making and painting it I went up the tower for another job and confirmed the fit. I left it up there for a few weeks until I had a chance to do the swap.

Swapping the boom-to-mast clamp of a 60 lb (27 kg) yagi with a 32' (10 m) boom is not a trivial repair job. What holds the antenna when the old clamp is removed? How do you keep it from shifting and making it difficult to align the holes so that the saddle clamps can be installed on the new clamp?

You may be surprised to learn that it isn't very difficult. The job took 30 minutes, only requiring several feet of malleable stranded steel utility cable and a tow strap. The latter was only necessary because the utility cable wasn't quite long enough.

The cable was thrown over the upper strut of the side mounted rotator assembly. Each end was looped around the boom and twisted together. This is enough to support the antenna when the clamps are loosened. As mentioned earlier, a strap was used on one end to make up for the short length of cable.

Does that sound surprising? Much of the yagi's weight is supported by the boom truss, not the boom-to-mast clamp. When the clamp is removed it won't drop far due to that support. The steel cable is more important for reducing boom sag so that the new clamp can be attached with only a little muscle to return it to the same position on the mast.

As you can see in the picture the mast clamps were removed first and transferred to the new plate. The yagi swung to my left because the mast is not at the yagi's CoG (centre of gravity). This was done to minimize the phase shift relative to the upper 5-element yagi when one or both are rotated, thus retaining stacking gain. That was discussed in the earlier article about this rotatable side mount.

The new plate is lightly clamped to the mast while the old plate is removed from the boom. At the time the picture was taken one of the boom clamps is still attached to the old plate. Notice the tape markers on mast and boom that indicate the 4 edges of the old plate. Those help to align the clamps for the new plate.

You might think that the yagi would be wildly out of control at this point especially since it was breezy during the operation. That didn't happen. The boom truss clamp on the mast keeps the yagi pointing the same direction. If the freely hanging antenna wobbles it soon resumes its correct position. It is only the boom sag and tilt that must be managed. 

With the old plate out of the way the new one was slid down the mast. I held a boom clamp (saddle and u-bolt) around the boom with one hand and swung the yagi right with my other hand. When the boom was level and centred on the plate the u-bolts were inserted into the plate and secured. This would have been easier with a rope tying the boom to the tower to keep the boom levelled and centred. Since I hadn't packed a short rope I fussed with it for a minute until the second boom clamp was driven home.

Once all the clamps were on it was pretty easy to align the boom on the plate in accord with the tape markers. The new plate is obviously smaller than the old one. Its size is suitable, it's just that the old junk box aluminum plate was larger than necessary. It just happened to be the first suitable plate that I found in my junk box.

The boom is about 1" little lower than before. Sighting along the boom indicated that it is still very level and pointing at the horizon in both direction despite the slight sag. I saw no reason to fuss with it further and declared the job complete.

If the new clamp rotates on the mast I'll replace the mast with a steel pipe of the same size: 1.9" O.D., nominal 1-½" pipe size, schedule 40. Hopefully that won't be necessary.

No comments:

Post a Comment

All comments are moderated, and should appear within one day of submission.